A line integral can accumulate a scalar quantity along length, or record work along an oriented path. Their parameter formulas look similar enough to confuse, but the distinction determines the speed factor, the effect of reversing direction, and the interpretation of a path that retraces itself.
This section develops the two definitions into weighted-wire mass, center of mass and axis moments. The measure here is length, not area.
Study route
This unit derives both pullback formulas from a parametrization, proves their reversal rules, identifies what a physical density means after a change of parameter, and sets up wire mass and moments. You need the chain rule, one-variable substitution and elementary definite integrals.
The norm in ds has a purpose
Definition 4.6.1
(Scalar line integral)
Let a curve be described by a piecewise map , and let be continuous on its trace. The scalar line integral along this traversal is
On a short parameter interval, the displacement is approximately . Its length is approximately . This explains the speed multiplier: equal parameter increments need not represent equal lengths.
Definition 4.6.2
(Work integral)
For a continuous vector field on the trace, the oriented work along the same traversal is
Here the vector displacement retains its direction. Replacing it with its norm would change the quantity being measured. Conversely, multiplying a scalar density by only one coordinate derivative would not measure total length.
These formulas apply piece by piece. For the physical wire calculations below, the parametrization covers the wire once, apart from finitely many shared endpoints, and the density is continuous and nonnegative with positive total mass. A traversal with repeated arcs is a different counting prescription.
Common mistake
(Forgetting the speed)
For the semicircle , , and density , the integral is not the mass. The speed is , so the mass is , which is the length of the wire. Equal parameter increments are not equal lengths.
Quick check
(Find the mass of the straight wire , , with density .)
Compute the speed first, and evaluate on the curve.
Solution · Answer
, so , and . Then .
Concept lensAnalytic
Arc length as the parameter
On a smooth piece where never vanishes, put . This is an increasing bijection onto , with the length, and . Substituting for turns the scalar integral into along a unit-speed curve, so the speed factor is exactly the Jacobian of this substitution. For the semicircle of radius above, and the mass is .
A density belongs to the point, not the parameter name
Suppose is mass per unit length. The mass of a once-covered wire is
If the same wire is reparametrized by , the density becomes . One must compose its old parameter expression with .
For example, on a rising helix with , a spatial density becomes . If the reversed path uses , its density is , not . The function assigning density to each physical point has stayed fixed.
Theorem 4.6.3
(Reparametrization of line integrals)
Let be piecewise , let be a monotone bijection with nowhere zero, and put . Then the scalar line integral of a continuous along equals that along , whereas if is increasing and if is decreasing.
Proof
(Chain rule and substitution)
The chain rule gives , hence
The substitution therefore preserves the scalar integral for either direction of travel: for decreasing the limits swap, and restores the sign. In the work integral the factor is , without absolute value. An increasing change preserves work; a decreasing change negates it.
Proof X-ray
Absolute value for speed, sign for velocity
The one non-routine point is that a single chain-rule factor enters the two integrands differently. The velocity keeps the sign of , but its norm needs , because a length is nonnegative. After , the factor becomes over and the scalar integral is unchanged, while becomes and work is multiplied by the sign. Monotonicity is what makes keep one sign. If went forward and then back over part of the arc, that part would be traversed twice: the scalar integral would count it twice and the work over it would cancel, as in the return trip below.
The hypotheses specify a sufficient reparametrization class. A map whose derivative vanishes at an isolated point can still be handled directly by the integral formula, but it is not covered by the nowhere-zero-derivative statement as written.
Worked example 4.6.4
(A helix and its reversed parametrization)
Let , , with . The speed is and , so
and . Reverse the path with . The speed is unchanged, the density is and , so and , in agreement. For the field the work is along and along .
Common mistake
(Reusing the old density after reversing)
In the reversed helix, using instead of still gives the correct mass , because both integrals equal , so the error is easy to miss. The first moment exposes it: gives the wrong height instead of .
First moments and the center of mass
Definition 4.6.5
(First moments and center of mass)
For positive mass, define
The center of mass is
This follows from the usual finite weighted average by replacing small masses with . It is a consequence of the scalar line-integral definition, not a separate vector-calculus theorem.
Every coordinate of the center lies between the corresponding minimum and maximum coordinates of the wire. Indeed, if , multiply by nonnegative density and integrate to obtain . Division is valid because . The center need not lie on the wire: a curved wire's weighted average can lie away from its trace.
Worked example 4.6.6
(A semicircular wire with density y)
Let , , with . The speed is , so . Then and , so . This point has distance from the origin, so it is not on the wire. On the wire , so , and the formula of the next section gives , which is positive as it must be.
A geometric reflection determines a coordinate only when the density also respects that reflection. A helix with increasing density has different weights at points that happen to share a geometric-looking symmetry.
Counterexample mode
A symmetric trace with an asymmetric density
The claim that for any wire whose trace is symmetric about the axis is false. Take the semicircle , , with density , which is nonnegative on the wire. Then and , so . The reflected density differs from , so the density does not respect the symmetry.
Axis moments use perpendicular distance
The moment of inertia about the axis is
For a planar wire in , the perpendicular-axis moment about the origin is
For the perpendicular axis through its center of mass, expand the actual distance:
The cancellation uses and . The weight and denominator are the wire mass. Area formulas from a planar lamina do not apply just because the wire lies in a plane.
A nonnegative density is needed for the physical interpretation and coordinate bounds. A signed scalar integrand is still a legitimate line-integral integrand, but a zero signed total cannot serve as a mass denominator.
A return trip counts twice for mass and cancels for work
Consider a once-covered arc from to , followed immediately by the same arc in reverse. Add the two integrals over their parameter intervals. The scalar integrals are equal, so the combined value is twice the single-traversal value. The work integrals are opposites, so their sum is zero for every continuous field defined on the arc; no potential is needed for this cancellation.
If the path describes travel, double counting is appropriate for accumulated distance or exposure. If it describes a single physical wire, counting the same material twice would overstate its mass. The trace alone does not specify which interpretation is intended.
Worked example 4.6.7
(A quarter circle traversed there and back)
Let , , followed by its reverse, and let . Along one pass , and along the reverse pass it is , so the total work is , although has no potential. With the scalar integral is for each pass and in total, twice the length of the arc. If the path models a single wire, its mass is , not .
Quick check
(Compute for along , , and along the reversed path.)
Use .
Solution · Answer
, so the work is . The reversed path gives .
Quick check
(A straight wire of length m has density kg/m. A path goes along it and back. What is over the path, and what is the mass of the physical wire?)
Distinguish the path from the wire.
Solution · Answer
Each pass contributes kg, so the path integral is kg. The physical wire has mass kg; the extra kg comes from counting the same material twice.
The same distinction applies to first and second scalar moments. A complete second traversal doubles mass and every moment, leaving their center-of-mass ratios unchanged. Consequently, a plausible center cannot establish that mass or traversal multiplicity was correct.
Checklist before calculating
- Write the parameter interval, compute every component of velocity, and take its Euclidean norm for .
- Evaluate the spatial density on the curve. Compose that density again after any parameter change.
- Identify whether the model is a once-covered wire or a path with repeated travel.
- Use signed velocity for work and nonnegative speed for a scalar length integral.
- Divide weighted first moments by mass, check positivity and coordinate ranges, and state the chosen axis in a second-moment integrand.
- Check that a claimed symmetry preserves the density as well as the trace.